Ignition Mini tachometer Ver 3.0

»óÇ°À̹ÌÁö
RPMÀ» ½Ç½Ã°£À¸·Î üũ!

»óÇ°°¡ 19,800¿ø

¹è¼Ûºñ (Á¶°Ç) Áö¿ªº°

ÆäÀ̽ººÏ Æ®À§ÅÍ
»ó¼¼Á¤º¸ »õâ ¿­±â

»ó¼¼ Á¤º¸¸¦ È®´ëÇØ º¸½Ç ¼ö ÀÖ½À´Ï´Ù.

Ignition Mini tachometer Ver2.[Hard Case]


À̱״ϼǰú Ȧ¼¾¼­ »çÀÌ¿¡ ³¢¿ö ½Ç½Ã°£ ¿£ÁøÀÇ RPM¸¦ Check Çϴ ȹ±âÀûÀÎ ITEMÀÔ´Ï´Ù.
ÀüÀÚ¹æ½ÄÀ¸·Î Á¤È®ÇÑ ÃøÁ¤ÀÌ °¡´ÉÇÕ´Ï´Ù.

(Àü¿ë YÄÚµå´Â Æ÷ÇԵǾî ÀÖ½À´Ï´Ù!).


»óÇ°±¸¼º:
-Ignition Mini Tachometer :1°³
-YÄÚµå:1°³


ÁÖÀÇ»çÇ×:
-DLE¿£Áø ¹× OS¿£Áøµî, RCXEL»çÀÇ À̱״ϼǿ¡¸¸ »ç¿ë°¡´ÉÇÕ´Ï´Ù.!


»óÇ°»ó¼¼¼³¸í:

1. Use PIC16f628a microcontrollers
2. Do not need batteries,Power from the ignition
3. Standard FUTABA plug(Black-Negative Red-Positive and White-Signal)
4. Using high-brightness LED digital tube.
5. ÀÔ·ÂÀü¾Ð :3.5V-12.0V
6.Àü·ù¼Ò¸ð·®: 25mA-60mA
7. Mini tachometer indicates up to 30000 rpm
8. Actual RPM= Display Digital *10
9. Àüü»çÀÌÁî: 41mm L x 17mm W x 12mm H
10.¾×Á¤»çÀÌÁî: 30mm L x 15mm H
11.¹«°Ô:8.5g 

Instructions:
1.The Y wiring tandem between in the HALL sensor and the ignition.
2.The tachometer plug the other end with Y wire.
3.Connected to ignition power supply and can be displayed
Note:
That connecting plugs do Reinforcement. To prevent vibration.
The hall sensor & tachometer wire Leave from the Ignition high-voltage wire,
And receiver wires over 30cm
Connection tachometer is not recommended after the use of flight,
Best to remove the Y wire to restore the original sensor connection
If ignition have an additional tachometer pinout.
You must be connected to dedicated tachometer signal wire.

Note:
Can not guarantee that other types of ignition can use the tachometer And guarantee accuracy




ºñ¹Ð¹øÈ£ È®ÀÎ ´Ý±â